Turbine Oil Coalescing Systems

Improved Oil Processing with Low Maintenance SystemVelcon TOC Series Filter Vessels

Turbine Oil Coalescing Systems TOC Series - Data Sheet #1751

5 GPM Turbine Oil Coalescing System TOC5-1 - Data Sheet #1857

Velcon Filters has over 50 years experience designing and manufacturing coalescing filtration equipment. The TOC Series units combine the latest coalescing technology with the finest available microglass filter media to restore turbine lube oil to an exceptionally clean and dry condition. The units can be used to upgrade or replace older, low efficiency reservoir filtration systems.

PERFORMANCE

SIMPLICITY

Velcon TOC Filter SystemRELIABILITY

SPECIFICATIONS

Electrical
TOC Filtration SystemMechanical
General

 

HOW IT WORKS

The TOC Series Turbine Oil Coalescing Systems remove water and dirt from turbine lube oil. Contaminants are removed in stages (see photo) A, B, and C:

A. Particulate solid contaminants are removed in the Pre-Filter stage (#8 in diagram below) by cost effective, high surface area pleated synthetic media cartridges. This extends the life of the specialized filters downstream.

B. Free and emulsified water are removed in the Filter/Separator stage (#10 below). Finely dispersed water passes through the coalescer element and grows into larger drops. These drops collect in the vessel sump where they are drained. A Teflon® coated screen separator prevents any small water drops from entering the effluent oil stream. Fine particulate solid contaminants are also removed by the coalescer elements.

C. The final Polishing stage (#14 below, optional on TOC10) uses synthetic media elements to remove fine particles.TOC Filter System

TOC Series Flow Diagram

1 Inlet Suction Strainer
2 Motor
3 Pump with Integral Pressure Relief
4 Manual Flow Bypass
5 Adjustable High Pressure Shut-Off Switch
6 P1 Inlet Pressure Gauge
7 Differential Pressure, Pre-Filter
8 Pre-Filter Stage
9 P2 Pressure Gauge
10 Filter/Separator Stage
11 Differential Pressure, F/S Vessel
12 P3 Pressure Gauge
13 Differential Pressure
14 Polishing Filter Stage (Optional on TOC10)
15 Effluent Sample Tap

CARTRIDGES AND GASKETS

Stage
TOC10
TOC30
PRE-FILTER
VF82SYS150
VF82SYS150

FILTER CARTRIDGE

FOS-618PLP8
FOS-618PLP8

QTY REQUIRED

2
2

RECOMMENDED SPARES

4
4

LID GASKET

G-1045
G-1045

RECOMMENDED SPARES

1
1
FILTER/SEPARATOR
HV1622TO30
HV2233SYS150

COALESCER CARTRIDGE

CC-62285
CC-63385

QTY REQUIRED

3
4

RECOMMENDED SPARES

3
4

SEPARATOR CARTRIDGE

SO-424V
SO-430C

QTY REQUIRED

1
2

RECOMMENDED SPARES

-
-

LID GASKET

G-2033
G-2036

RECOMMENDED SPARES

1
1
POLISHING FILTER
VF82SYS150
VF82SYS150

FILTER CARTRIDGE

FOS-618PL1/2
FOS-618PL1/2

QTY REQUIRED

2
2

RECOMMENDED SPARES

2
2

LID GASKET

G-1045
G-1045

RECOMMENDED SPARES

1
1

SPECIFICATIONS

 
TOC10
TOC30
FLOWRATE
10 GPM
30 GPM
MOTOR HP
1 HP
2 HP
CONNECTION SIZE
1" MALE CLAMP
1.5" MALE CLAMP
DIMENSIONS (LxWxH)*
40" x 51" x 60"
42" x 66" x 60"
WEIGHT*
1,241 LBS`
1,750 LBS
SHIPPING WT*
1,650"
2,250

*For a basic unit with no options

ORDERING INFORMATION

Specify model number as shown below. Units are shipped with one set of cartridges installed.

TOC10-1 115 v, 1 ph, 60 Hz
TOC10-2 or TOC30-2 230 v, 1 ph, 60 Hz
TOC10-3 or TOC30-3 230 v, 3 ph, 60 Hz
TOC10-4 or TOC30-4 460 v, 3 ph, 60 Hz

Also available: 50 Hz power, explosion proof motor, variable speed motor, low RPM motor (contact factory).

OPTIONS & ACCESSORIES

TOC10 TOC30  
552Z040 552Z050 Filter Bypass
553Z040 553Z050 4-Way Inlet Valve
724Y030 724Y030 High Water Level Shut-Off
025Y006 N/A Polishing Filter Vessel
491Y001 491Y002 Polyurethane Casters (TOC10: 8”, TOC30: 10”)
491Y010 491Y012 Pneumatic Casters (TOC10: 10”, TOC30: 12”)
661Y012 661Y012 Remote Stop/Start Switch (w/25 ft cord)
744Y003 744Y001 Hour Meter
722Y006 722Y006 Digital Flowmeter/Totalizer

Also available: inlet oil heaters, auto water drain (contact factory). 

RECOMMENDED SPARES

See Cartridges and Gaskets Table